| Part | Description |
| A5191-63004 | Data cable - Has 10-pin (F) connectors - From PCI I/O backplane to disk/media backplane |
| A5191-63005 | SCSI ribbon cable - One 68-pin (M) connector on each end - 51.6cm (20.3in) long - SCSI bus-A - From four port SCSI card to drive/media backplane |
| A5191-63006 | SCSI ribbon cable - One 68-pin (M) connector on each end - 39.6cm (15.6in) long - SCSI bus-B - From 4-port SCSI card to drive/media backplane |
| A5191-63007 | Ultra SCSI ribbon cable - Two 50-pin (M) connectors - 29.5cm (11.6in) long - SCSI bus-RM - From 4-port SCSI card to drive/media backplane |
| A5191-63008 | SCSI ribbon cable with termination - Has two 50-pin (F) connectors - 9.7cm (3.8in) long - From DVD-ROM drive to disk/media backplane |
| A5191-63009 | Power cable assembly - Large 6-pin (F) connector to small 6-pin (F) connector - 8.3cm (3.3in) long - For the rear chassis fan |
| A5191-63010 | Power cable assembly - Large 6-pin (F) connector to small 6-pin (F) connector - 20.2cm (8.0in) long - For the front chassis fan |
| A5191-63011 | Ribbon cable - Has two 10-pin (F) connectors - 54cm (21.3in) long - From system board to display board |
| A5191-63013 | Drive power cable - Has two 4-pin (F) connectors - 13.5cm (5.3in) long - From DDS drive to disk/media backplane |
| A5191-63014 | SCSI ribbon cable with termination - Has two 50-pin (F) connectors - 17.5cm (6.9in) long - From DDS drive to disk/media backplane |
| A5191-67006 | 'Hot swap' fan for the power converter |
| A5191-67012 | New part for A5191-69112 |
| A5191-67104 | Disk/media backplane - Has power and SCSI connectors for removable media mass storage devices on one side and four SCA connectors for hot-plug hard drives on the other side |
| A5191-67210 | New part for A5191-69210 |
| A5191-67211 | New part for A5191-69211 |
| A5191-69105 | Power converter - Converts the input voltage 100/240V to power that can be used by the power supplies - Has three power cord input plugs |
| A5191-69112 | PCI GSP - Provides virtual front panel functionality and remote management capabilities through a 25-PIN RS232 serial port or an RJ-45 10Base-T LAN port - L-Class PCI GSP - Provides virtual front panel functionality and remote management capabilities thro |
| A5191-69210 | Platform monitor PC board - Plugs into the system board at the back of the chassis |
| A5191-69211 | 10/100Base-T LAN / 4 port Ultra2 LVD SCSI PC board - Has one external RJ-45 LAN port and one 68-pin Ultra2 LVD Very High Density SCSI port and two internal 68-pin Ultra2 LVD SCSI ports and one 50-pin Ultra SCSI2 port |
| A5191-70010 | Bezel hardware kit - Used with new style (one piece) front bezel |
| A5220-67003 | Narrow Single-Ended SCSI-2 slot load DVD-ROM drive - 6X DVD-ROM read, 32X CD-ROM read (Pioneer DVD-303/304) - Has headphone jack and volume control - May be used as replacement for a CD-ROM drive |
| A5527-69001 | Hot-swap redundant power supply - 100/240VAC input, 50/60Hz, autoswitching |
| A5527A | Hot-swap redundant power supply - 100/240VAC input, 50/60Hz, autoswitching |
| A5554-60002 | New part for A5554-69002 |
| A5554-69002 | 128MB ECC high-density SDRAM DIMM memory module - Must be installed in pairs of equal size (256MB kit is A5554A) |
| A5554A | 256MB ECC DIMM high-density memory upgrade kit - Includes two 128MB SDRAM DIMM modules |
| A5557A | Narrow Single-Ended SCSI-2 slot load DVD-ROM drive - 6X DVD-ROM read, 32X CD-ROM read (Pioneer DVD-303/304) - Has headphone jack and volume control |
| A5558A | 12GB/24GB Single-Ended SCSI-2 DDS-3 (DAT) tape drive - 5.25in form factor |
| A5570-62014 | Processor terminator module |
| A5796A | PA-RISC 8500/8600 processor support module - Provides power for two processors - One required for every two processors |
| A5797-60001 | New part for A5797-69101 |
| A5797-69101 | 256MB ECC high-density SDRAM DIMM memory module - Must be installed in pairs of equal size (512MB kit is A5797A) |
| A5797A | 512MB ECC DIMM high-density memory upgrade kit - Includes two 256MB SDRAM DIMM modules |
| A5798-60001 | New part for A5798-69001 |
| A5798-69001 | 512MB ECC high-density SDRAM DIMM memory module - Must be installed in pairs of equal size (1024MB kit is A5798A) |
| A5798A | 1024MB ECC DIMM high-density memory upgrade kit - Includes two 512MB SDRAM DIMM modules |
| A5802-67003 | New part for A5802-69003 |
| A5802-69003 | 9GB hot-plug Ultra2 Low Voltage Differential (LVD) SCSI SCA hard drive - 10,000 RPM, low profile (Seagate) |
| A5802A | 9GB hot-plug Ultra2 Low Voltage Differential (LVD) SCSI SCA hard drive - 10,000 RPM, low profile |
| A5802AR | 9GB hot-plug Ultra2 Low Voltage Differential (LVD) SCSI SCA hard drive - 10,000 RPM, low profile |
| A5803-67002 | New part for A5803-69003 |
| A5803-69003 | 18GB hot-plug Ultra-2 SCSI hard drive module - 10,000 RPM, low profile (Seagate ST318404LC) |
| 257894-006 | HPCC Myrinet Fiber NIC |
| 264007-B21 | Slimline DVD-ROM Drive (8X/24X) Option Kit |
| 273911-B21 | Ultra320 Expansion Module for SA-6402 |
| 273913-B21 | 256MB DDR, Battery-Backed Cache Upgrade Kit for SA-6400 |
| 273914-B21 | Smart Array 6404/256 Controller |
| 273915-B21 | Smart Array 6402/128 Controller |
| 274338-B22 | HP StorageWorks 3U Rack-mount kit |
| 286776-B22 | HP 36GB U320 15K Universal HDD |
| 286778-B22 | HP 72GB U320 15K Universal HDD |
| 288874-B21 | DL580 G3 Cable Assembly, SCSI, Ultra3, LVDS |
| A5803A | 18GB hot-plug Ultra-2 SCSI hard drive module - 10,000 RPM, low profile |
| A5803AR | 18GB hot-plug Ultra-2 SCSI hard drive module - 10,000 RPM, low profile |
| A6091A | 73GB hot-plug Ultra2 SCSI hard drive - 10,000 RPM, low profile |
| A6091AR | 73GB hot-plug Ultra2 SCSI hard drive - 10,000 RPM, low profile |
| A6110-67002 | New part for A6110-69003 |
| A6110-69003 | 36GB hot-plug Ultra-2 Low Voltage Differential (LVD) SCSI SCA hard drive - 10,000 RPM, low profile (Seagate) |
| A6110A | 36GB hot-plug Ultra-2 Low Voltage Differential (LVD) SCSI SCA hard drive - 10,000 RPM, low profile (Seagate) |
| A6110AR | 36GB hot-plug Ultra-2 Low Voltage Differential (LVD) SCSI SCA hard drive - 10,000 RPM, low profile (Seagate) |
| A6115-60002 | New part for A6115-69002 |
| A6115-69002 | 1024MB ECC high density SyncDRAM memory module - Must be installed in pairs of equal size (2048MB Kit is A6115A) |
| A6115A | 2048MB ECC high-density memory upgrade kit - Includes two 1024MB SDRAM DIMM modules |
| A6144-00001 | System board area access cover/top plate - Has four holes for the top of the processors |
| A6144-00002 | Platform monitor card guide |
| A6144-00003 | L3000 system Board mounting plate |
| A6144-00004 | L3000 front card guide |
| A6144-00005 | L3000 rear card guide - Card guide for the memory boards |
| A6144-63004 | Power harness kit - Includes two mounting screws and a PC board with a DB-25 (M) connector, a 4.1cm (1.6in) ribbon cable with a 20-pin (F) connector, and a 12.3cm (4.8in) cable with a 6-pin (F) connector - From the power converter to the system board |
| A6144-67002 | New part for A6144-69102 |
| A6144-69102 | PCI I/O backplane board - Has 12 PCI slots - L3000 PCI I/O backplane board - Has 12 PCI slots - Mounts vertically in the chassis |
| A6146-04001 | New part for A6146-69001 |
| A6146-69001 | HP PA-RISC processor - 550MHz PA-RISC 8600 with 1.5MB cache - Includes attached heat sink |
| A6146A | HP PA-RISC processor upgrade kit - Includes one 550MHz PA-RISC 8600 processor with 1.5MB cache and attached heat sink - Operates at 540MHz in L1000 and Level-2000 systems |
| A6150A | PCI 2D graphics kit - Includes one 2D PCI graphics card and one PCI 2 port USB card |
| A6150B | PCI 2D graphics kit - Includes one 2D PCI graphics card and one PCI 2-port USB card |
| A6155-60001 | New part for A6155-69001 |
| A6155-69001 | Memory carrier - Has eight DIMM slots - L3000 Memory carrier - Has eight DIMM slots - Attaches to the system processor board |
| A6155A | Memory carrier - Adds an additional eight DIMM slots - L3000 memory carrier - Attaches to the system processor board |
| A6583A | PowerTrust II-MR Uninterruptible Power Supply - 4.5KVA, 4000 watt, 240VAC - Includes one battery pack, RS232 DB9/DB9 standard cable, rack kit, and manuals |
| A6586A | 240V Battery pack - 25A, external - For PowerTrust II-MR 4000W UPS |
| A6797-67101 | New part for A6797-69101 |
| A6797-69101 | System board - For 1-4 way processor configuration |
| A6798-04001 | New part for A6798-69001 |
| A6798-69001 | HP PA-RISC processor - 650MHz PA-RISC 8700 with 1.5MB cache - Includes attached heat sink |
| A6798A | HP PA-RISC processor - 650MHz PA-RISC 8700 with 1.5MB cache - Includes attached heat sink |
| A6799A | PA-RISC 8700 processor support module - Provides power for two processors - One required for every two processors |
| A6805-04001 | New part for A6805-69001 |
| A6805-69001 | HP PA-RISC processor - 750MHz PA-RISC 8700 with 1.5MB cache - Includes attached heat sink |
| A6805A | HP PA-RISC processor - 750MHz PA-RISC 8700 with 1.5MB cache - Includes attached heat sink |
| C1537-67202 | New part for C1537-69202 |
| C1537-69202 | 12GB/24GB Single-Ended SCSI-2 DDS-3 (DAT) tape drive - 5.25-inch form factor - (part of A3542A, A4249A) |
| C2364A | Low voltage differential/single-ended SCSI terminator - Has 68-pin high density (M) connector with thumbscrews |
| C2370A | Low voltage differential/single-ended SCSI terminator - Has 68 pin very high density connector with thumbscrews |
| C2905A | High voltage differential SCSI terminator - Has 68 pin high density (M) connector with thumbscrews |
| 8120-6899 | Power cord - Has CEE 7/7 (M) plug for power input and C19 (F) plug for power output - 4.5m (14.8ft) long |
| 8120-6903 | Power cord (Black) - 15 AWG, 4.5m (14.8ft) long - Has NEMA L6-20P (M) plug for power input and (F) C19 receptacle for power output (for the United States, Canada, and Japan) |
| 8120-6961 | Daisy chain' power cord (Black) - 14 AWG, 4.0m (13.1ft) long - Has (M) C20 plug for power input, and (F) C19 plug for power output |
| 8121-0161 | Power cord (Black) - 15 AWG, 2.5m (8.2ft) long - Has (M) 90 degree power plug and straight (F) C19 receptacle (For 220V in Israel) |
| A5198-69101 | 512MB high-density SyncDRAM DIMM memory |
| AD247A | HP Integrity rx2660 PCI-e and PCI-x combo cage option (2/1) |
| AD248A | Controller for internal storage (required for Windows, optional for other operating systems] |
| AD249A | 1.6 GHz/6 MB single-core processor module |
| AD252A | 1.4 GHz/12 MB dual-core processor module |
| AD253A | Rack kit for factory and field racking |
| AD254A | HP Integrity rx2660 redundant hotswap power supply (optional -- max 1) |
| AD265A | 300 GB HotPlug Ultra 160 SCSI low profile disk (15 K) |
| AD273A | 1 GB Chip Spare DDR2 memory pair (2x 512 MB) |
| AD274A | 2 GB Chip Spare DDR2 memory pair (2 x 1 GB DIMMs) |
| A5486A | HP SpeedCard - PCI accelerator board for public key cryptography |
| A5515A | 155Mb/s ATM PCI UTP5 LAN adapter with MMF connectors |
| A6092A | HyperFabric PCI 4X fiber adapter interface |
| A6093-00239 | SCSI interface board |
| A6093-40041 | PCI OLR gate (latch) - Secures the PCI card and enables the PCI slot |
| A6093-63025 | Chassis intrusion switch cable |
| A6093-63044 | Chassis intrusion switch cable |
| A6093-67114 | PCI OLR latching assembly - Disables PCI slots for hot-swap functionality and retains the PCI cards - Includes four OLR housings, 16 OLR buttons, PC board, 16 OLR paddles, and OLR switch cable |
| A6093-69123 | PCI power supply module - Hot-swap power module for the PCI backplane |
| A6094-69103 | Cell board/PDH riser card assembly - Cell board mounted on metal tray, has four processor sockets and 16 DIMM slots |
| A6094A | Processor and memory cell board assembly |
| A6097A | 2GB high-density SyncDRAM DIMM memory upgrade (set of four 512MB DIMMs) |
| A6098-60101 | New part for A6098-69101 |
| A6098-69101 | 1GB high-density SDRAM DIMM (single DIMM) |
| A6098A | 4GB high-density SyncDRAM DIMM (Set of four 1GB DIMMs) |
| A6180A | 6x DVD-ROM read, 32x CD-ROM read Single-Ended SCSI-2 slot load DVD-ROM drive - Has headphone jack and volume control - (Pioneer DVD-303/304) |
| A6182A | DAT40I - 20/40GB DDS-4 internal tape drive |
| AD276A | 8 GB Chip Spare DDR2 memory pair (2 x 4 GB DIMMs) |
| A6443-69001 | HP PA-RISC processor - 650MHz PA-RISC 8700 with 2.25MB cache - Includes attached heat sink and processor socket |
| A6443A | HP PA-RISC processor upgrade - Includes two 650MHz PA-RISC 8700 processors with 2.25MB cache, attached heat sink, and processor socket |
| A6443AX | New part for A6443-69001 |
| A6444A | HP PA-RISC processor upgrade - Includes two 750MHz PA-RISC 8700 processors with 2.25MB cache, attached heat sink, and processor socket |
| A6537-67002 | New part for A6537-69003 |
| A6537-69003 | 18GB hot-swap Ultra 160 Low Voltage Differential SCSI hard drive module - 10,000 RPM, low profile |
| A6541-60001 | New part for A6541-69002 |
| A6541-69002 | 36GB hot-swap Ultra160 Low Voltage Differential SCSI hard drive module - 15,000 RPM, low profile |
| A6584A | PowerTrust II-MR Uninterruptible Power Supply - 9.0KVA, 6500 watt, 240VAC - Includes one battery pack set with 2 batteries, RS232 DB9/DB9 standard cable, rack kit, and manuals |
| A6585A | PowerTrust II-MR Uninterruptible Power Supply - 12.0KVA, 8000 watt, 240VAC - Includes one battery pack set with 2 batteries, RS232 DB9/DB9 standard cable, rack kit, and manuals |
| A6723A | 18GB 'hot swap' Low Voltage Differential Ultra-3 SCSI disk module - 10000 RPM, low profile |
| A6725A | 73GB hot-swap Low Voltage Differential Ultra3 SCSI disk module - 10000 RPM, low profile |
| A6752-00123 | AC cord retention bracket |
| A6752-04002 | Chassis assembly |
| A6752-04017 | Core I/O slot filler panel |
| AD280A | HP 16 port RS-232 RJ45 Port Module, min 1, max 4 Port Modules per AD279A |
| AD281A | HP 16 port RS-232 DB25 Port Module, min 1, max 4 Port Modules per AD279A |
| A6752-04066 | Front bezel assembly - Does not include the nameplate |
| A6752-63033 | Mass storage power cable (Cable #1) |
| A6752-63034 | Mass storage power cable #2 |
| A6752-67003 | Mass storage backplane - Has four SCA SCSI connectors for hot-swap drives, mounts in the back of the hard drive cage |
| A6752-67005 | Front display panel - Has seven activity LEDs, power button, metal mounting bracket, and 36.8cm (14.5in) long ribbon cable |
| A6752-67011 | CD/DVD-ROM drive mounting rail |
| A6752-67014 | New part for A6752-69014 |
| A6752-67021 | DVD-ROM drive power cable |
| A6752-67022 | Front and rear hot-swap system fans power cable |
| A6752-67025 | Main system power harness |
| A6752-67029 | Front/rear hot-swap smart fan assembly |
| A6752-67030 | Smart fan assembly - For hot-swap PCI card cage |
| A6752-67036 | PCI card cage access panel |
| A6752-67041 | DVD-ROM drive bay filler panel |
| AD300A | Dual port 4 GB Fibre Channel, PCI-e |
| A6752-69001 | System backplane - Has slots for cell boards and core I/O boards and connectors for system cables - Mounts vertically on the left side of the system |
| A6752-69014 | PCI backplane (card cage assembly) - Includes the metal PCI backplane cage and the 16 slot PCI backplane |
| A6752-69113 | Hot-swap redundant power supply module |
| A6793-69001 | Core I/O interface board - Hot-swap I/O board |
| A6793A | Core I/O interface board - Has one Ultra3 SCSI port, one 10/100/1000BaseT LAN port, web console connector, and three RS-232 serial ports |
| A6794-60001 | New part for A6794-69001 |
| A6794-69001 | LAN/SCSI core I/O PCI board (Procurium) |
| 5065-5227 | Disk Tray |
| AD313A | Dual-port 4X Fabric HCA (HPC & DB), PCI-e |
| AD317A | HP PCI Audio Card for servers |
| AD331A | HP PCI-X 1port 1000Base-T Adapter (5701) |
| AD332A | Single-port GigE-SX (optical) adapter card for HP-UX and OpenVMS |
| AD333A | 146 GB/10K 2.5" SAS hard disk drive |
| AD335A | Smart Array P800 (PCI-e) |
| AD33A | 146 GB/10k SAS hard disk drive |
| A6746-60001 | 512MB PC2100 ECC DDR266 MEM |
| A6870A | RX2600 Base System |
| A9667-62010 | Intel Itanium 2 processor - 1.5GHz |
| A6802-60001 | New part for A6802-69101 |
| A6802-69101 | 256MB high-density SyncDRAM DIMM (single DIMM) |
| A6802A | 1GB high-density SyncDRAM DIMM (Set of four 250MB DIMMs) |
| A6831A | 36GB hot-swap Ultra160 Low Voltage Differential SCSI hard drive module - 15,000 RPM, low profile |
| AB297-63001 | PCI OLR ribbon cable |
| C5686-69203 | DAT40I - 20/40GB DDS-4 internal tape drive |
| 399542-291 | 700W HP redundant power supply with IEC cord and Japan cord (Japan) |
| J1530A | Field rack mount kit for rpXXXX series servers |
| J2484A | HP RJ45/RS-232 16 Port MUX Multiplexer interface module |
| J2485A | HP DB25/RS-232 16 Port MUX Multiplexer interface module |
| J2488A | RJ45 to HP-RJ45 converter |
| J2501A | HP RS-422/RJ45 16 Port MUX Multiplexer interface module |
| J3830A | RJ45 to HP-DB25 converter for Multiplexer |
| 0950-3794 | New part for A6093-69021 |
| 0950-4122 | Low voltage DC to DC conterter (low voltage VRM) |
